| 268 |
Guard for magneto contact arm |
| 322 |
Spanner, claw, for plug |
| 323 |
Extractor for spindle, idler gears, auxiliary drive |
| 324 |
Tool for locking gear on main driving shaft when meshing magneto drive gears |
| 326 |
Tool for threading nut on stud for accessories and supercharger to crankcase |
| 327 |
Holder for gear, metering pump drive |
| 328 |
Holder for air compressor drive gear |
| 329 |
Holder for right-hand intermediate drive gears |
| 330 |
Holder for generator drive idler gears |
| 331 |
Holder for main drive shaft |
| 332 |
Guide for assembling oil seal |
| 400 |
Holder for cover when assembling bearings, coolant seal and spannering retaining nut |
| 401 |
Spanner, claw, for nut retaining bottom bearing |
| 402 |
Holder for impeller spindle when spannering impeller retaining nut and rotating spindle when lapping seal |
| 403 |
Holder for impeller spindle when spannering ring nut |
| 404 |
Spanner, claw, for ring nut on impeller spindle |
| 405 |
Drift for dismantling top ball bearing from cover |
| 406 |
Drift for dismantling bottom ball bearing from cover |
| 407 |
Drift for assembling ball bearings in cover |
| 408 |
Drift for assembling coolant seal in cover |
| 409 |
Holder for casing |
| 431 |
Spanner, claw, for assembling plugs in propeller shaft oil feed passage. Alternative to item 120 |
| 432 |
Shield for preventing connecting-rods damaging crankcase cylinder openings |
| 433 |
Key for plug, hydraulic propeller feed, in crankcase front end, right-hand half |
| 434 |
Spanner, ring, 7/16" B.S.F. for nut on stud in front wall securing crankcase halves |
| 435 |
Spanner, ring, 7/16" B.S.F., slotted for split pin, for nut on stud in front wall securing crankcase halves |
| 436 |
Spanner, ring, 5/16" B.S.F. for nuts securing crankcase halves at auxiliary drive idler gear, and bolts at starter intermediate gear |
| 437 |
Spanner, box, 5/16" B.S.F. for nuts and bolts securing crankcase halves at starter intermediate gear |
| 438 |
Cap for retaining propeller shaft rear bearing in crankcase when tightening nut, retaining housing of hydromatic propeller oil feed |
| 439 |
Spanner, claw, for cap nut on banjo, hydromatic propeller oil feed |
| 440 |
Spanner, claw, for nut retaining idler gear rear roller bearing, sleeve drive |
| 441 |
Spanner, claw, for nut retaining housing, hydromatic propeller oil feed to crankcase |
| 442 |
Tool for assembling rear bearing and housing for layshaft reduction gears |
| 443 |
Tool for assembling housing and outer race, front bearing idler gears, sleeve drive |
| 444 |
Extractor for front bearing idler gears, sleeve drive |
| 445 |
Extractor for idler gears, sleeve drive |
| 446 |
Tool for assembling rear bearing and liner, idler gears |
| 447 |
Extractor for rear roller bearing and housing and front outer race and housing, idler gear shaft sleeve drive |
| 448 |
Spanner, box, 1/2" B.S.F., extension for nuts, crankcase bolts. For dismantling. Use with item 123 |
| 449 |
Spanner, box, 7/16" B.S.F., extension for nuts, crankcase centre bearing bolts. For dismantling purposes only |
| 450 |
Extractor for bearing and housing, layshaft rear bearing, reduction gears in crankcase |
| 451 |
Foot support for crankcase |
| 452 |
Strip, protecting studs |
| 453 |
Spanner, claw, for ring nut, sleeve idler gear retaining bolt, crankcase. For dismantling purposes only |
| 454 |
Spanner, claw, for ring nut, sleeve idler gear retaining bolt, crankcase. For use with torquometer, item 637 |
| 455 |
1/2" square adapter for torquometer |
| 456 |
Grub screw for adapter (part of item 455) |
| 457 |
Sleeve, guiding connecting rods when assembling crankshaft in crankcase |
| 458 |
Spanner, box, 1/2" B.S.F. for cylinder block I and crankcase nuts. For use with adapter and grub screw, items 455 and 456 |
| 459 |
Spanner, box, 7/16" B.S.F. for cylinder head nuts, and nuts of crankcase centre bearing bolts. For use with adapter and grub screw, items 455 and 456, and torquometer, item 637 |
| 480 |
Spanner, claw, for nut for coolant pump drive gear |
| 481 |
Spanner, claw; for nut retaining fuel pump driving gear, lower |
| 482 |
Spanner, claw, for nut retaining fuel pump driven gear |
| 483 |
Spanner, claw, for plug in bottom cover |
| 484 |
Extractor for driving gear, oil and coolant pumps drives |
| 485 |
Holder for coolant pump drive gear |
| 486 |
Holder for oil and coolant pumps drive gear |
| 487 |
Spanner, claw, for nut retaining driving gear and nut on coupling shaft, crankcase bottom cover |
| 488 |
Tool, holding supercharger scavenge oil pump cover |
| 500 |
Spanner, ring, 5/16" B.S.F. for oil seal bolts and nuts, crankcase journals and crankpins |
| 501 |
Spanner, ring, for crankshaft front nut |
| 502 |
Tool for locking crankshaft when assembling cylinder block |
| 503 |
Sling bar for crankshaft when assembling in crankcase |
| 522 |
Tool for lowering cylinder block on to crankcase |
| 523 |
Spanner, claw, for plug, oil gallery in cylinder block |
| 524 |
C-spanner for screwed connection, coolant pump to inlet manifold on cylinder block |
| 525 |
Tool for locating gear, sleeve drive, cylinder block |
| 526 |
Spanner, box, for elbows, oil pipe from reducing valve |
|
| 527 |
Spanner, claw, for nut retaining driving gear hub, sleeve and supercharger drive shaft |
| 528 |
Plate, slinging, for cylinder block |
| 529 |
Holder for driving gear, rear, and hub for supercharger shaft |
| 530 |
Holder for wormshaft front half |
| 531 |
Tool, for holding gear and hub when spannering nuts, supercharger drive |
| 532 |
Spanner, box, 5/16" B.S.F. for nuts retaining worm gear housings. (For use with torquometer) |
| 533 |
Key, 5/16" square for core plug on inner face |
| 534 |
Key, 7/16" square for core plugs |
| 535 |
Key, 5/8" square for flanged plug. Induction and coolant manifolds |
| 536 |
Key, 7/8" square for core plug |
| 537 |
Tool for removing wormshaft intermediate and thrust bearings |
| 538 |
Tool for removing wormshaft front bearing |
| 553 |
Tool for compressing piston rings when used in conjunction with item 828. Used alone for compressing cylinder head compression ring |
| 554 |
Tool for removing cylinder head from cylinder block |
| 556 |
Spanner, box, 3/8" B.S.F. for cylinder head nuts. For use with torquometer, item 636 |
| 581 |
Holder for plunger when spannering retaining nut on relief valve |
| 600 |
Holder for valve when spannering nut |
| 626 |
1/8" x 3/16" x 16 s.w.g., 9/32" bar holes |
| 627 |
1/4" x 5/16 " x 14 s.w.g., 9/32" bar holes |
| 628 |
3/8" x 7/16" x 13 s.w.g., 13/32" bar holes |
| 629 |
1/2" x 9/16" x 11 s.w.g.,17/32" bar holes |
| 630 |
Spanner, open double-ended, 11/16" x 3/4" B.S.F. |
| 631 |
Spanner, open double-ended, 9/16" x 5/8" B.S.F. |
| 632 |
Spanner, ring, double-ended, 1/4" x 5/16" B.S.F. |
| 633 |
Spanner, ring, double-ended, 5/16" X 3/8" B.S.F. |
| 634 |
Spanner, ring, double-ended, 3/8" x 7/16" B.S.F. |
| 635 |
Spanner, ring, double-ended, 7/16" x 1/2" B.S.F. |
| 636 |
Torquometer Model No. TQ.50A. Capacity 600 lb in with adapter A-2, for use with spanners, items 532, 556, and 930 |
| 637 |
Torquometer Model No. TQ.15 or 150. Capacity 150 lb ft for use with spanners, items 454, 458, 459, 467, 829, 830 and 957 |
| 638 |
Torquometer Model No. TQ.352. Capacity 350 lb ft for use when spannering fixtures, items 958, 962 and 963 |
| 639 |
Bar, tommy, 3/16" diameter |
| 641 |
Bar, tommy, 5/16" diameter |
| 642 |
Bar, tommy, 3/8" diameter |
| 682 |
Spanner, claw, for nut retaining wormshaft |
| 683 |
Spanner, claw, for nut retaining wormshaft |
| 684 |
Holder for starter claw, turning gear intermediate drive |
| 685 |
Clamp for compressing spring in throw-out gear |
| 686 |
Holder, splined for driving bevel gear |
| 687 |
Holder, splined for wormshaft when spannering ring nuts |
| 688 |
Extractor for wormshaft ball bearings |
| 689 |
Holder for intermediate drive gears and worm-wheel |
| 730 |
Spanner, box, 3/16" square for screws securing ignition control unit inner cover |
| 731 |
Tool, holding contact point (B.T.H. magneto) when filing |
| 784 |
Spanner, box, universal joint, 7/32" B.S.F. for flange nuts, oil delivery pipe to cooler |
| 785 |
Spanner, box, for nut (14 mm.) for oil pipe banjo, Heywood compressor |
| 802 |
Spanner, claw, for cap, shut-off valve in oil sump |
| 803 |
Spanner, claw, for sleeve nut in filter body extension in oil sump |
| 804 |
Support for oil pressure pump and relief valve housing in oil sump |
| 805 |
Support for oil pressure pump and relief valve housings in oil sump |
| 806 |
Support for oil sump (bottom faces) when fitting and cutter-facing bushes |
| 820 |
Spanner, box, 3/8" B.S.F. for cap nuts, forked rod. For dismantling purposes only |
| 821 |
Spanner, box, 7/16" B.S.F. for cap nuts, plain rod. For dismantling purposes only |
| 822 |
Locating pin for connecting-rod nuts |
| 823 |
Ram for pressing on gudgeon-pin circlip |
| 824 |
Guide for gudgeon-pin circlip |
| 825 |
Drift for gudgeon-pin |
| 826 |
Pliers for gudgeon-pin circlip |
| 827 |
Holder for gudgeon-pin when pressing on circlip |
| 828 |
Compressor sleeve for piston and scraper rings when assembling cylinder blocks |
| 829 |
Spanner, box, 3/8" B.S.F. for cap nuts, forked rod. For use with torquometer, item 637 |
| 830 |
Spanner, box, 7/16" B.S.F. for cap nuts, plain rod. For use with torquometer, item 637 |
| 831 |
Compressor band for piston and scraper rings and cylinder head compression ring on intermediate cylinders, when assembling cylinder blocks |
| 852 |
Spanner, claw, for right-angle drive housing cap in housing |
| 853 |
Spanner, claw, for nut for reduction gear driving bevel, right-angle drive |
| 854 |
Tool for holding gear, driven, for use with item 853 |
| 870 |
Tool for assembling and extracting propeller shaft and cover |
| 871 |
Holder for propeller shaft |
| 872 |
Spanner, claw, for nut for fulcrum pin 1 |
| 873 |
Holder for assembling and dismantling bearings and housings in reduction gear carrier |
| 874 |
Drift for assembling roller bearings and assembling and extracting bearing housing |
| 875 |
Drift for extracting layshaft front bearing |
|
| 876 |
Screw, extractor for reduction gear carrier |
| 877 |
Spanner, box, No. 4 B.A. for setscrew retaining plate, hydromatic propeller oil feed |
| 878 |
Spanner, claw, for nut retaining spring, hydromatic propeller oil feed |
| 879 |
Presser for locking washer, hydromatic propeller oil feed |
| 880 |
Spanner, claw, for nut retaining layshaft front bearing balance arm fork, and nut for starter intermediate drive |
| 881 |
Spanner, claw, for nut retaining layshaft front bearing on balance arm fork |
| 882 |
Spanner, claw, for nut retaining layshaft ball bearing on balance arm fork, and nut retaining layshafts, high- and low-speeds supercharger clutch shaft drive |
| 883 |
Spanner, claw, for nut retaining layshaft gear |
| 884 |
Holder for thrust fork for use with spanners, items 881 and 882 when spannering nuts |
| 885 |
Extractor, for cone for propeller shaft |
| 886 |
Spanner, box, 3/8" B.S.F. for nut (inner) housing, securing propeller shaft front bearing housing |
| 887 |
Tool, holding, for layshaft and gear-wheel when spannering nuts |
| 888 |
Spanner, box, single-ended, 3/4" Whitworth x 11 s.w.g., 17/32" bar holes for plugs securing ring tank supports in propeller shaft cover |
| 889 |
Tool for removing and assembling bearing housing in propeller shaft cover |
| 890 |
Tool for removing and assembling propeller shaft bearings in housing |
| 891 |
Extractor for pad, front, in balance arm |
| 892 |
Drift for locking shrouded washer for nut retaining tail plug |
| 893 |
Spanner, claw, for nut for tail plug in propeller shaft |
| 894 |
Drifts and extractors for assembling and dismantling reduction gear layshafts |
| 895 |
Extractor for bearing and sleeve on thrust fork |
| 896 |
Plate, protecting face of tail plug when de-tabbing locking washer in propeller shaft |
| 897 |
Drift for driving out tail plug in propeller shaft |
| 898 |
Spanner, claw, for nut retaining balance arm damper |
| 899 |
Extractor ring for collar on propeller shaft (for use with item 885) |
| 919 |
Timing fixture for upper auxiliary drive shaft |
| 920 |
Spanner, claw, for nut securing wormwheel |
| 921 |
Timing fixture for sleeve drive shaft |
| 922 |
Tool for setting sleeves for use with timing dial in conjunction with item 921 |
| 923 |
Gauge, ring, for timing sleeve position in relation to crankshaft |
| 924 |
Timing fixture for crankshaft (prior to Mod. 513) |
| 925 |
Plate for retaining scraper rings when timing sleeves |
| 926 |
Spanner, claw, for nuts, worm-shaft drive gear bolts and nuts, crankshaft starter drive gear bolts and hand-turning gear driving gear bolts (for strip only) |
| 927 |
Extractor for bearing cap, worm housing |
| 928 |
Holder for sleeve drive crankshaft for use with item 920 |
| 929 |
Extractor for sleeve drive worm gear housing |
| 930 |
Spanner, claw, for nuts, worm-shaft drive gear bolts, crankshaft starter drive gear bolts and turning gear driving gear bolts (for use with torquometer TQ50A) |
| 952 |
Holder for gear, low-speed clutch shaft (pre-Mod. 596) |
| 953 |
Spanner, claw, for nut retaining inner race for front bearing, low-speed clutch shaft |
| 954 |
Holder for housing, low-speed clutch shaft front bearing |
| 955 |
Spanner, claw, for nut retaining outer race, front bearing, low-speed clutch shaft |
| 956 |
Holder for gear, high-speed clutch shaft |
| 957 |
Spanner, claw, for nut retaining gear, high-speed clutch shaft. For use with torquometer, item 637 |
| 958 |
Spanner, claw, for nut, impeller shaft front bearing inner race. For use with torquometer, item 638 |
| 959 |
Spanner, claw, for nut, front bearing outer race, impeller shaft |
| 960 |
Extractor for gear, high-speed clutch shaft |
| 961 |
Extractor for supercharger control valve |
| 962 |
Tool for spannering nut retaining clutch cover. For use with torquometer, item 638 |
| 963 |
Tool for spannering nut retaining clutch outer cone. For use with torquometer, item 638 |
| 964 |
Holder for clutch housing |
| 965 |
Gauge, plug limit for bore of high-speed clutch shaft |
| 966 |
Extractor for split bush, front, for impeller |
| 967 |
Fixture for checking truth of oil seal carrier rings, clutch and impeller assembly |
| 968 |
Tool, holding, for clutch housing when spannering nut retaining impeller front bearing; and nut retaining high-speed clutch shaft gear |
| 969 |
Tool for checking impeller blade clearance |
| 970 |
Extractor for housing of impeller shaft front bearing |
| 971 |
Holding tool for layshaft assembly |
| 972 |
Tool for removing rear ball bearing from clutch housing |
| 973 |
Tool for removing clutch housing |
| 974 |
Extractor for impeller drive gear, front, ball bearing and housing for low-speed shaft |
| 975 |
Holder for low-speed shaft |
| 976 |
Plate, slinging, for supercharger |
| 977 |
Tool for assembling clutch housing into rear ball bearing |
| 978 |
Spanner and holding tool for nut retaining outrigger bearing |
| 979 |
Extractor screw for cover and outrigger bearing housing. Clutch housing and sump |
| 980 |
Tool for spannering air vent elbow on supercharger |
|
